發電機組是一種起動迅速、操作維修方便、投資少、對環境的適應性能較強的發電裝置。那么發電機組的機油中是怎么混入水的呢？下面沼氣發電機組廠家為您分析分析：

The generator set is a kind of power generation device with fast starting, convenient operation and maintenance, low investment and strong adaptability to the environment. So how does the oil of the generator set mix with water? The following biogas generator unit manufacturers will analyze for you:

①水堵壓裝不緊導致松脫漏水；水堵爛透。

① The water plug is not tightly pressed, resulting in looseness and water leakage; The water is blocked and rotten.

解決的辦法是更換水。

The solution is to replace the water.

水堵在缸體內面，看不到，其外面是(在排氣管側的工藝堵。若水堵孔腐蝕嚴重或碰損，應用銑刀擴孔少許，再選大一號水堵或自己車削一個水堵?lián)Q上。

The water plug is on the inner surface of the cylinder block and cannot be seen. The outer part is the process plug (on the exhaust pipe side). If the water plug hole is seriously corroded or damaged, use a milling cutter to expand the hole a little, and then select a larger water plug or turn a water plug by yourself to replace it.

②氣缸墊損壞或缸蓋裂紋，水進入氣門推桿孔而順流到油底殼內。

② The cylinder head gasket is damaged or the cylinder head is cracked, and the water enters the valve pushrod hole and flows into the oil pan.

氣缸墊沖燒，往往伴有哧哧的響聲；有時，水漏入氣缸中，此時燃燒排氣的煙色為白霧狀。仔細判斷是哪一個缸損壞了，可用停缸法判斷。查找判準后，更換氣缸墊，若是缸頭裂紋或砂眼，則可視情修理或更換。

When the cylinder gasket is burned, it is often accompanied by a wheezing noise; Sometimes, water leaks into the cylinder, and the smoke color of combustion exhaust is white fog. Carefully judge which cylinder is damaged, and use the cylinder shutdown method to judge. After finding and determining, replace the cylinder gasket. If the cylinder head cracks or sand holes, repair or replace them as appropriate.

③機體上有砂眼。

③ There are sand holes on the body.

特別是在缸體上的水室部位，該部位有主油道，與主軸瓦孔有斜油道相通，如有砂眼、縮松等鑄造缺陷，將有水漏入油底殼內。可卸下油底殼查看，若發現主軸瓦孔處出水，則說明油道與水室相通。若檢查冷卻液，則其內一定混入機油漂浮其上。若無機油漂浮，則說明砂眼在其它部位，認真觀察缸體內什么部位漏水。為確保發動機的使用，更換缸體總成，防止出現化瓦事故。

Especially in the water chamber on the cylinder block, there is a main oil passage, which is connected with the inclined oil passage of the main bearing hole. If there are casting defects such as sand holes and shrinkage porosity, water will leak into the oil pan. The oil pan can be removed for inspection. If water is found at the main bearing hole, it means that the oil passage is connected with the water chamber. If the coolant is checked, it must be mixed with oil and float on it. If there is no oil floating, it means that the sand hole is in other parts. Carefully observe which part of the cylinder leaks. In order to ensure the use of the engine, replace the cylinder block assembly to prevent the occurrence of the accident.

發電機組的機油中是怎么混入水？這個問題，我們從三個方面來為您講解完畢了，您是否了解了呢？更多事項就來我們網站http://www.hdlelisa.com咨詢吧！

How is water mixed in the engine oil of the generator set? We have explained this question to you from three aspects. Do you understand it? Come to our website for more matters http://www.hdlelisa.com Ask!