瓦斯發電機組在正常使用過程中，可能會由于各種原因導致進水，那么發電機組進水后還能不能繼續使用?下面和小編一起來了解一下。

During the normal use of the gas generator set, water may enter the water due to various reasons. Can the generator set continue to be used after water enters the water? Let's have a look with Xiao Bian.

我們要了解為什么會進水：

We need to understand why water enters:

1、由于燃油箱沒有清洗干凈，只要清洗干凈了就基本不會出現進水現象。

1. Because the fuel tank is not cleaned, as long as it is cleaned, there will be no water ingress.

2、油品有問題，小編建議用戶到正規加油站購買的，從私人或無資質的企業購買的便宜燃油極可能混有過多雜質或水分。

2. There is a problem with the oil. Xiaobian suggests that the cheap fuel purchased from private or unqualified enterprises from regular gas stations may be mixed with too much impurities or moisture.

3、燃油箱只有兩個口，一個機和燃油箱連接的是高壓油泵，一般不可能是發動機出問題這邊的水回流。

3. There are only two ports in the fuel tank. One engine is connected to the fuel tank by a high-pressure oil pump. Generally, it is not possible that the engine has a problem.

另一個入口就是燃油箱加油口，如果燃油箱處于室外，是很有可能雨水滲入燃油箱內部。

The other entrance is the fuel tank filler. If the fuel tank is outside, it is likely that rain will seep into the fuel tank.

小編提醒各位進水后是不能繼續使用的，因為水是無法被壓縮的，油水混合進入到汽缸后，發動機依然還牌調整運轉期間，做功的過程中不能對水進行壓縮，從而導致活塞卡死，汽缸磨損情況會變得加劇。

The editor reminds you that water can't be used after water ingress, because water can't be compressed. After oil and water are mixed into the cylinder, the engine is still under adjustment and operation, and water can't be compressed during work, resulting in piston seizure and cylinder wear.

如果中有水，除了會導致發電機組運轉緩慢且不穩定之外，甚至還可能造成曲軸彎曲等，對發電機組的正常運行帶來非常嚴重的影響。

If there is water in it, in addition to causing slow and unstable operation of the generator set, it may even cause bending of the crankshaft, which will have a very serious impact on the normal operation of the generator set.

一般發生發電機組進水后，要盡快把電瓶負極線拆下來，以免發電機的控制系統因時水而發生短路，同時按正確步驟更換燃油濾清器。

Generally, after water enters the generator set, remove the negative wire of the battery as soon as possible to avoid short circuit of the control system of the generator due to water. At the same time, replace the fuel filter according to the correct steps.

如果進水不是很多，可以先讓靜置一段時間，讓水慢慢沉淀下去，等到水和成分層后，再將水排凈即可。而如果是進水的量比較大，則應將原有的變質全部更換，否則可能會造成機組運行冒白煙或運行無力。更多相關事項就來我們網站http://www.hdlelisa.com咨詢！

If there is not much water inflow, you can let it stand for a period of time, let the water settle down slowly, and then drain the water after the water and the composition layer. However, if the amount of water inflow is large, the original deterioration should be replaced completely, otherwise it may cause white smoke or weak operation of the unit. Come to our website for more relevant matters http://www.hdlelisa.com consulting service