在修理瓦斯發電機組時，通常需要清潔機油，碳沉積物，水垢和鐵銹的零件表面。由于各種污物的性質不同，去除方法也不同。那么下面小編就來為您講解下瓦斯發電機的各種垢物的清洗方法。

When repairing a gas generator set, it is usually necessary to clean the surface of parts with oil, carbon deposits, scale and rust. Due to the different properties of various pollutants, the removal methods are also different. Then the following editor will explain the cleaning methods of various dirt of the gas generator for you.

油污清洗：零件表面的油污沉積較厚時應先刮除。二手瓦斯發電機出租清洗零件方法，一般清洗零件表面油污，常用的清洗液有堿性清洗液和合成洗滌劑。使用堿性清洗液進行熱清洗時，加熱至70~90℃，將零件浸入10~15min，然后取出并用清水沖洗干凈，再用壓縮空氣吹干。

Oil stain cleaning: when the oil stain on the surface of the part is thick, it should be scraped off first. Second hand gas generator rental cleaning method of parts, generally cleaning oil stains on the surface of parts, commonly used cleaning solutions include alkaline cleaning solution and synthetic detergent. When using alkaline cleaning solution for hot cleaning, heat it to 70 ~ 90 ℃, immerse the parts in water for 10 ~ 15min, then take them out and wash them with clean water, and then blow them dry with compressed air.

注意：使用汽油清洗不安全；鋁合金零件不能在強堿性清洗液中清洗；非金屬類橡膠零件應使用酒精或制動液進行清洗。

Note: it is not safe to use gasoline for cleaning; Aluminum alloy parts cannot be cleaned in strong alkaline cleaning solution; Non metallic rubber parts shall be cleaned with alcohol or brake fluid.

積炭清除：清除積炭可使用簡單的機械清除法。即用金屬刷子或刮刀等進行清除，但此方法不易將積炭清除干凈，而且易損傷零件表面。采用化學方法清除積炭，即先使用退炭劑（化學溶液）加熱至80~90℃，將零件上的積炭膨脹軟化，然后再用毛刷等進行清除。

Carbon deposit removal: simple mechanical removal method can be used to remove carbon deposits. That is, use a metal brush or scraper to remove it, but this method is not easy to remove the carbon deposits, and it is easy to damage the surface of the parts. Remove the carbon deposit by chemical method, that is, heat the carbon remover (chemical solution) to 80 ~ 90 ℃, expand and soften the carbon deposit on the parts, and then remove it with a brush.

水垢的清除：瓦斯發電機清洗一般采用化學清除法，將清除水垢的化學溶液加入到冷卻液中，發動機工作一定時間后，再更換冷卻液。常用清除水垢的化學溶液有：苛性鈉溶液或鹽酸溶液、氟化鈉鹽酸除垢劑和磷酸除垢劑，磷酸除垢劑適合用于清除鋁合金零件上的水垢。

Scale removal: chemical cleaning method is generally adopted for gas generator cleaning. The chemical solution for scale removal is added to the coolant. After the engine operates for a certain time, the coolant is replaced. Common chemical solutions for removing scale include caustic soda solution or hydrochloric acid solution, sodium fluoride hydrochloric acid scale remover and phosphoric acid scale remover. Phosphoric acid scale remover is suitable for removing scale on aluminum alloy parts.

上述就是小編為大家介紹的有關簡單敘述如何清洗瓦斯發電機的垢物的內容，大家對此還有什么感到疑問需要了解的，歡迎大家前來咨詢我們網站http://www.hdlelisa.com進行咨詢。

The above is what Xiaobian introduced to you about how to clean the scale of the gas generator. If you have any questions or need to know about this, you are welcome to consult our website http://www.hdlelisa.com Consult.