燃?xì)獍l(fā)電機組的控制模塊報警提示單缸出現爆震無法正常運行，導致這一現象的原因?yàn)槭裁茨?？下面來簡單的為您講解一番吧。

The control module of the gas generator set gives an alarm that the single cylinder can not operate normally due to knocking. What is the reason for this phenomenon? Let me explain briefly for you.

加熱值設置不合理，校正系統存在誤差;出現了爆震傳感器故障或存在電路故障;進氣溫度過高;進氣外立面閥座處或活塞頂部等燃?xì)馐抑谐霈F(xiàn)大量積碳。具體的診斷方法為：

The setting of heating value is unreasonable, and there is error in the correction system; Knock sensor fault or circuit fault occurs; The intake air temperature is too high; There is a large amount of carbon deposition in the gas chamber such as the valve seat on the intake facade or the top of the piston. The specific diagnosis method is:

檢查進氣溫度是否符合正常標準，依據氣體溫度高的檢查方式進行故障排查;對熱值及來氣濃度的匹配狀況進行檢測，對熱值進行合理調整，保障修正系統處于100%的運行狀態，這一系統若低于95%就會引發爆震;

Check whether the inlet air temperature meets the normal standard, and conduct troubleshooting according to the inspection method of high gas temperature; Detect the matching condition of calorific value and incoming gas concentration, adjust the calorific value reasonably, and ensure that the correction system is in 100% operation state. If the system is lower than 95%, it will cause detonation;

安裝新的傳感器以判斷原有的傳感器是否存在故障問題，并對爆震線路與插頭進行檢查，如未能發現故障還需布設零時線進行排查;對氣缸內氣面門以及氣門座等位置的積碳情況進行檢查，排查氣缸內部是否存在泄露情況，先用氣缸壓表測量，如無異常也可進行拆缸檢查。

Install a new sensor to determine whether the original sensor has fault problems, and check the knock circuit and plug. If no fault is found, it is necessary to arrange a zero time line for troubleshooting; Check the carbon deposition at the air valve and valve seat in the cylinder, check whether there is leakage inside the cylinder, measure with the cylinder pressure gauge first, and disassemble the cylinder for inspection if there is no abnormality.

此外在啟動過程中，通常會出現啟動時電機無轉速電池電壓恒定不變的情況，有時也會發生盤車有速度但機組難以啟動的現象這一現象產生的直接原因通常為電池容量不足接線電纜出現損毀;火花塞等點火系統出現故障;啟動電機出現故障問題;啟動壓力不足等原因。

In addition, in the process of startup, the motor has no speed and the battery voltage is constant. Sometimes, the turning gear has speed but the unit is difficult to start. The direct cause of this phenomenon is usually the insufficient battery capacity and the damage of the wiring cable; Failure of ignition system such as spark plug; Failure of starting motor; Insufficient starting pressure, etc.

燃?xì)獍l(fā)電機組在使用期間可能會出現這樣那樣的問題，所以為了更順利的使用起來，建議早些了解相關早些預防，關注我們http://www.hdlelisa.com，帶你了解更多！

Problems may occur during the use of the gas generator set. Therefore, in order to use it more smoothly, it is recommended to learn about the relevant problems and prevent them earlier and pay attention to us http://www.hdlelisa.com Yes, I'll show you more!