對于新買的焦化發電機組需要進行磨合再投入使用，在磨合過程中主要是保證潤滑劑、軸承等能夠適應后面的持續運行。下面小編就來向大家介紹發電機組的磨合相關知識：

The newly purchased coking generator set needs to be run in before it is put into use. In the process of running in, it is mainly to ensure that the lubricants and bearings can adapt to the subsequent continuous operation. The following editor will introduce the running in knowledge of generator sets to you:

1、空載發電機組，按前方法進行認真檢查，各方面均很正常后，即可啟動機組。機組啟動后，將轉速調整至怠速，運轉10分鐘。并檢視機油壓力，傾聽焦化機運轉聲響，然后停車。

1. The no-load generator set shall be carefully checked according to the previous method. After all aspects are normal, the unit can be started. After the unit is started, adjust the speed to idle speed and run for 10 minutes. Check the oil pressure, listen to the running sound of the coking machine, and then stop.

2、打開汽缸體側蓋板，用手觸摸主軸承、連桿軸承等處的溫度，要求不應高于80℃,即不太燙手為正常，并觀察各機件運轉情況。若各機件溫度及結構均正常之后，再按下述規范繼續進行磨合。

2. Open the side cover plate of the cylinder block, touch the temperature of the main bearing, connecting rod bearing, etc. by hand, which should not be higher than 80 ℃, that is, it is normal if it is not too hot, and observe the operation of all parts. If the temperature and structure of all parts are normal, continue to run in according to the following specifications.

3、發動機的轉速由怠速逐步升高至額定轉速，高空載轉速運轉時間應不超過5-10min。在磨合期間，冷卻水溫應保持在75-80℃，機油溫度不應高于90℃。

3. The engine speed gradually increases from idle speed to rated speed, and the operating time at high no-load speed shall not exceed 5-10min. During running in, the cooling water temperature shall be kept at 75-80 ℃, and the engine oil temperature shall not be higher than 90 ℃.

4、在使用過程中，由于冷卻系統結構的限制，工作負荷及轉速的變化，環境溫度的改變等因素，使焦化機工作溫度的變化范圍很大。實踐表明，冷卻水溫度控制在75~85℃，潤滑油溫度在75~95℃時為有利。

4. During use, due to the limitation of the cooling system structure, the change of the working load and speed, the change of the ambient temperature and other factors, the operating temperature of the coking machine varies widely. Practice shows that it is advantageous to control the temperature of cooling water at 75 ~ 85 ℃ and the temperature of lubricating oil at 75 ~ 95 ℃.

這里小編再次提醒下大家新買的焦化發電機組一定進行磨合后再投入使用。您想了解更多相關內容就來我們網站http://www.hdlelisa.com咨詢看看吧。

Here, Xiaobian reminds you again that the newly purchased coking generator set must be run in before it is put into use. If you want to know more about it, please come to our website http://www.hdlelisa.com Let's consult.