The smooth grinding of the crankshaft of gas-fired generator set is one of the key processes to ensure the repair quality. When taking the cylindrical surface of timing gear journal and flywheel flange as the reference for smooth grinding and paste loading, the curvature must be corrected before grinding. The runout of the middle main journal before grinding shall not be greater than o.3mm. If the bending is not corrected in advance, after weaving and cutting, the crankshaft will produce a new axis intersecting with the original flywheel flange and the axis of the timing gear, which changes the turning radius, destroys the dynamic balance force, shortens the service life, intensifies the wear of relevant parts, the noise of the timing gear is also large, and the rear oil seal leaks, increasing the unbalanced rotation quality of the engine.

嚴格保證天然氣發電機組曲軸軸頸圓角半徑的尺寸符合圖紙要求，是修復質量的關鍵性問題之一。但一般汽車修理廠對此并沒有足夠的重視，砂輪很少修磨，光磨的圓角半徑常小于規定的尺寸。有資料統計，圓角半徑小于2，5毫米，其疲勞強度只及圓角半徑為2．5毫米的80％以下。由于對光磨曲軸的砂輪，經常用磨床附屬的砂輪圓角校正器修整，使磨得圓角尺寸符合要求，所以自振動堆焊投產以來，沒有發生過斷軸現象。

Strictly ensuring that the dimension of the fillet radius of the crankshaft journal of the natural gas generator set meets the requirements of the drawing is one of the key problems in the repair quality. However, the general automobile repair shop does not pay enough attention to this. The grinding wheel is rarely polished, and the fillet radius of smooth grinding is often less than the specified size. According to statistics, if the fillet radius is less than 2 or 5mm, its fatigue strength is only less than 80% of that of 2.5mm. Since the grinding wheel for smooth grinding of crankshaft is often trimmed with the grinding wheel fillet corrector attached to the grinder to make the grinding fillet size meet the requirements, there has been no shaft fracture since the vibration surfacing was put into operation.

天然氣發電機組在工作中，曲軸由于受力和工作條件復雜，各摩擦表面滑動速度很高，散熱條件又差，因此，曲軸的主軸頸和連桿軸頸在工作中不可避免地要產生磨損，而且磨損是不均勻的，其主要表現為軸頸出現圓度，圓柱度超過標準值和拉傷。連桿軸頸磨損的部位，一般在各軸頸的內側面上，即靠曲軸線一側，使軸頸失圓；而磨損成錐形的部位，一般在潤滑油道雜質附著的一側和受力大的部位上。曲軸主軸頸_的磨損部位，按發動機的強化程度、氣缸數、曲軸長度和平衡塊的配重不同而各異,而且相對于連桿軸頸磨損要均勻些。實踐表明,連桿軸頸的磨損比主軸頸磨損要快，但是，主軸頸磨損比連桿軸頸磨損所造成的后果要嚴重。

In the operation of natural gas generator set, due to the complex stress and working conditions of the crankshaft, the sliding speed of each friction surface is very high and the heat dissipation conditions are poor. Therefore, the main journal and connecting rod journal of the crankshaft will inevitably be worn in the operation, and the wear is uneven, which is mainly manifested in the roundness of the journal, the cylindricity exceeding the standard value and strain. The most worn part of the connecting rod journal is generally on the inner side of each journal, that is, the side close to the centerline of the crankshaft, which makes the journal out of round; The parts worn into a cone are generally on the side where impurities in the lubricating oil passage adhere and on the parts with large stress. Crankshaft main journal_ The wear parts vary according to the strengthening degree of the engine, the number of cylinders, the length of the crankshaft and the counterweight of the balance weight, and the wear is more uniform relative to the connecting rod journal. Practice shows that the wear of connecting rod journal is faster than that of main journal, but the consequence of main journal wear is more serious than that of connecting rod journal.

天然氣發電機組檢驗與處理方法。根據各軸頸磨損規律查找出磨損部位,可用外徑測微器測量其圓度和圓柱度以便確定曲軸的修理級別和磨削尺寸。

Inspection and treatment methods of natural gas generator set. Find out the worn parts according to the wear law of each journal, and use the outer diameter micrometer to measure its roundness and cylindricity, so as to determine the repair level and grinding size of the crankshaft.

曲軸的光磨加工情況，是保證修復質量的關鍵工序之一。以正時齒輪軸頸和飛輪突緣的外圓表面作為光磨裝-膏基準時，必須先校正彎曲度再進行磨削，磨前中間主軸頸的擺差不得大于o．3毫米。如果不預先校正彎曲，織削以后將會使曲軸產生與原來飛輪突緣和正時齒輪軸線交叉的新軸線，改變了回轉半徑，破壞了動平衡力，縮短使用壽命，加劇有關零件的磨耗，正時齒輪的響聲也大，后油封漏汕，增加了發動機的不平衡旋轉質量。

The smooth grinding of crankshaft is one of the key processes to ensure the repair quality. When taking the cylindrical surface of timing gear journal and flywheel flange as the reference for smooth grinding and paste loading, the curvature must be corrected before grinding. The runout of the middle main journal before grinding shall not be greater than o.3mm. If the bending is not corrected in advance, after weaving and cutting, the crankshaft will produce a new axis intersecting with the original flywheel flange and the axis of the timing gear, which changes the turning radius, destroys the dynamic balance force, shortens the service life, intensifies the wear of relevant parts, the noise of the timing gear is also large, and the rear oil seal leaks, increasing the unbalanced rotation quality of the engine.

嚴格保證曲軸軸頸圓角半徑的尺寸符合圖紙要求，是修復質量的關鍵性問題之一。但一般汽車修理廠對此并沒有足夠的重視，砂輪很少修磨，光磨的圓角半徑常小于規定的尺寸。有資料統計，圓角半徑小于2，5毫米，其疲勞強度只及圓角半徑為2．5毫米的80％以下。由于對光磨曲軸的砂輪，經常用磨床附屬的砂輪圓角校正器修整，使磨得圓角尺寸符合要求，所以自振動堆焊投產以來，沒有發生過斷軸現象。

Strictly ensuring that the dimension of the fillet radius of the crankshaft journal meets the requirements of the drawing is one of the key problems in the repair quality. However, the general automobile repair shop does not pay enough attention to this. The grinding wheel is rarely polished, and the fillet radius of smooth grinding is often less than the specified size. According to statistics, if the fillet radius is less than 2 or 5mm, its fatigue strength is only less than 80% of that of 2.5mm. Since the grinding wheel for smooth grinding of crankshaft is often trimmed with the grinding wheel fillet corrector attached to the grinder to make the grinding fillet size meet the requirements, there has been no shaft fracture since the vibration surfacing was put into operation.