大型焦化發電機組錯誤操作會嚴重影響焦化發電機組運用壽命，關于焦化發電機組的一些常見錯誤操作就讓小編來講講吧。

The wrong operation of large coking generator unit will seriously affect the service life of coking generator unit. Let's talk about some common wrong operations of coking generator unit.

1、焦化發電機在機油缺乏時運

1. Coking generator operates in case of oil shortage

焦化發電機在機油缺乏時運轉，會因機油供給缺乏而構成各摩擦副表面供油缺乏，招致異常磨損或燒傷。因此，焦化發電機起步前和焦化機運轉過程中要保證機油充足，防止由于缺油而惹起拉缸、燒瓦缺點。發電機組保養

When the coking generator runs in the absence of engine oil, the lack of engine oil supply will cause the lack of oil supply on the friction pair surfaces, resulting in abnormal wear or burns. Therefore, before starting the coking generator and during the operation of the coking machine, it is necessary to ensure that the oil is sufficient to prevent cylinder scuffing and bush burning due to lack of oil. Generator set maintenance

2、帶負荷急停機或突然卸除負荷后立刻停機

2. Emergency shutdown with load or immediate shutdown after sudden load removal

焦化機發電機熄火后冷卻系水的循環中止，散熱才干急劇降低，受熱件失去冷卻，易構成氣缸蓋、氣缸套、氣缸體等機件過熱，產生裂紋，或使活塞過度收縮卡死在缸套內。另一方面，焦化發電機停機時未經怠速降溫，會使摩擦面含油缺乏，當焦化機再次啟動時會因潤滑不良而加劇磨損。因此，焦化發電機熄火前應卸除負荷，并逐漸降低轉速、空載運轉幾分鐘。

After the coker generator is shut down, the circulation of cooling water stops, the ability to dissipate heat decreases sharply, and the heated parts lose their cooling, which is easy to cause overheating of cylinder head, cylinder liner, cylinder block and other parts, resulting in cracks, or make the piston shrink excessively and get stuck in the cylinder liner. On the other hand, when the coking generator is shut down without cooling at idle speed, the friction surface will be lack of oil. When the coking machine is started again, the wear will be aggravated due to poor lubrication. Therefore, the load of the coking generator shall be removed before the shutdown, and the speed shall be gradually reduced and the generator shall run for several minutes without load.

3、焦化發電機冷機啟動

3. Coking generator chiller start

焦化發電機冷機啟動時由于機油黏度大、活動性差，是機油泵供油缺乏，機器摩擦面因缺油潤滑不良，構成急劇磨損，以致發作拉缸、燒瓦等缺點。因此，焦化機冷卻啟動后應怠速運轉升溫，待機油溫度抵達40℃以上時再帶負荷運轉；機器起步應掛低速擋，并循序在每一擋位行駛一段里程，直到油溫正常、供油充分后，方可轉為正常行駛。

When the cold engine of the coking generator starts, due to the high viscosity and poor mobility of the oil, it is the lack of oil supply from the oil pump, and the lack of oil and poor lubrication on the friction surface of the machine, resulting in sharp wear, which leads to cylinder scuffing, bush burning and other defects. Therefore, the coker shall be operated at idle speed and heated up after cooling and starting, and then operated with load when the oil temperature reaches above 40 ℃; When starting, the machine should be put into low gear and driven for a certain mileage at each gear in sequence until the oil temperature is normal and the oil supply is sufficient.

4、焦化機冷啟動后猛轟油門

4. After cold start of coking machine, slam the accelerator

若猛轟油門，則焦化發電機轉速急劇升高，會構成機上的有些摩擦面因產生干摩擦而猛烈磨損。另外，轟油門時活塞、連桿和曲軸受理力變化大，惹起猛烈撞擊，易損壞機件。

If the accelerator is slammed, the speed of the coking generator will rise sharply, and some friction surfaces on the machine will be severely worn due to dry friction. In addition, the acceptance force of the piston, connecting rod and crankshaft changes greatly when the accelerator is slammed, causing violent impact and easy to damage the parts.

此外要知道焦化發電機過熱還會惡化焦化機熄滅過程，使噴油器工作失常，霧化不良，積炭增加，要避免此問題的出現，更多相關事項就來我們的網站http://www.hdlelisa.com咨詢吧！

In addition, it should be known that overheating of the coking generator will also worsen the quenching process of the coking machine, resulting in abnormal operation of the fuel injector, poor atomization, and increased carbon deposition. To avoid this problem, more relevant matters should come to our website http://www.hdlelisa.com Consult!