燃氣發電機組的電機軸使用期間，穩定性能真的是很重要，如果各方面不穩定的話就會對工作造成影響，甚至于對操作人員產生安全隱患，那么燃氣發電機組的電機軸穩定會受到什么影響？

　　During the use of the motor shaft of the gas generator set, the stability is really very important. If all aspects are unstable, it will affect the work, and even cause safety hazards to the operator. Then what will affect the stability of the motor shaft of the gas generator set?

　　電機軸不同于拖曳設備的軸，這導致開關磁阻電機上的徑向載荷過大，導致金屬疲勞。如果電機軸突出端的徑向載荷過大，電機軸將在徑向彎曲和變形。當電機旋轉時，軸會向各個方向扭曲變形，會損壞通常更靠近軸承的電機軸。

　　The motor shaft is different from the shaft of the towed equipment, which results in excessive radial load on the SWITCHED reluctance motor, leading to metal fatigue. If the radial load of the protruding end of the motor shaft is too large, the motor shaft will bend and deform in the radial direction. When the motor rotates, the shaft will distort in all directions, damaging the motor shaft, which is usually closer to the bearing.

　　對于由皮帶輪連接的電機，如果皮帶輪與開關磁阻電機的輸出軸匹配，在運行過程中，由于皮帶輪過重或皮帶過緊，可能會對電機的輸出軸產生很大的壓力。連續應力產生的較大彎矩位于輸出軸支點附近。

　　For a motor connected by a belt pulley, if the belt pulley matches the output shaft of the switched reluctance motor, during operation, there may be a lot of pressure on the output shaft of the motor due to the belt pulley being too heavy or too tight. The larger bending moment produced by continuous stress is located near the fulcrum of the output shaft.

　　如果反復沖擊，會產生疲勞，導致軸逐漸開裂，完全斷裂，運行設備和電機會嚴重損壞和晃動。如果電機固定不牢（如在機架上運行），運行時整個底座會不穩、抖動，電機皮帶的張力會不穩，張力會變大或減小，軸可能會損壞。

　　If repeated impact, fatigue will occur, leading to gradual cracking of the shaft, complete fracture, serious damage and shaking of operating equipment and electricity. If the motor is not fixed firmly （such as running on the rack）， the whole base will be unstable and jitter during operation, the tension of the motor belt will be unstable, the tension will be increased or decreased, and the shaft may be damaged.

　　燃氣發電機組電機軸加工應力槽不合格。故障是由軸直徑和徑向交變應力的影響引起的。如果軸徑變化很快，很容易斷裂，但問題比較小，與電機設計規格有關。如果電機的負荷瞬間過大，外力的沖擊也可能造成軸的損壞。

　　Motor shaft machining stress groove unqualified. The fault is caused by the influence of axial diameter and radial alternating stress. If the shaft diameter changes quickly, it is easy to fracture, but the problem is relatively small, and the motor design specifications. If the motor load is too large, the impact of external forces may also cause shaft damage.

　　燃氣發電機組的電機軸穩定會受到什么影響？以上就是問題的介紹了，只有您充分對其進行了解才能更好的保證電機組的使用和相關性能的發揮。更多內容就來網站www.hdlelisa.com進行咨詢吧。

　　What will affect the stability of the motor shaft of the gas generator set? The above is the introduction of the problem, only you fully understand it to better ensure the use of the generator unit and related performance. For more information, please visit www.hdlelisa.com.